HNS Technical Development Co. Ltd.
Gesztenyefa 4., Győr, 9027 Hungary
Phone: (96) 506-930
Fax: (96) 506-931
e-mail spc@hns.eu

If you are interested in our product, please ask for our offer!

HNS Geometry-2D
program system supporting two-dimension measurements for profile projectors and measuring microscopes

The program can be used for repeated and complex measurements, checking of size, form and position parameters, made by profile-projectors and measuring microscopes. HNS GEOMETRY-2D program ensures possibility for measurement of complex profiles quickly and easily supported by computer.

Advantages of using the program

In case of certain parts, it is not possible to make regular manual measurements because of the size, kind or complexity of the part - measurement of miniature parts, measuring in closed space, for example lamps, flexible parts, etc. -. In these cases, usually only touch-free measurements can be performed. In generally, only the simple measurements of lengths, and checking of the parts by patterns are performed touch-freely by profile-projector or measuring microscope, because the evaluating of complex geometries requires heavy calculation capacity.

HNS Geometry-2D program makes the measurements by touching points defined in coordinate system. User can assign the touching points of the part to be measured, and configure the evaluating of the touching points optionally, which is stored in a measuring program. Measuring of parts means running of the measuring programs made previously. In the course of the program's running, the touching points of the part are displayed one after the other, then, after reading-in the touching points, the results of the evaluating are displayed.

HNS Geometry-2D program supports complex two dimension measurements. Because of the previously created measuring programs, it is much easier and faster to perform the measurements - very complex measurements can be performed by operator-level staffs. The efficiency of the measurement will be much higher, because measurements are evaluated immediately and automatically.

Main features of the program

The program system ensures all kinds of support for planning the measurement of several parts and evaluation of measured coordinate data, for making the measuring programs, for checking the calculations recorded in the measuring program, and for daily using of the measuring programs.

• planning the measurement and appointing the touching points on the basis of the specifications of the drawn,
• planning the system and the order of the touching points,
• creating the picture of the measured part's shape,
• creating the measuring program,
• checking the measuring program with prepared measured values - coordinate data,
• control the measurements and geometric evaluation of the measuring points,
• forwarding the measured and calculated data to the HNS SPC program,
• printing measuring certificate at the end of the measurement.

HNS Geometry-2D program system consists of more functionally separated program modules. The modular structure allow of installing the program for different levels of users specially. On the engineer's workstations, there are available the functions which are needed for making and checking the measuring programs. On the operator's workstations - installed next to the producing machine or in the measuring laboratory -, it is enough to install the measuring module of the program.

The program receive the measured data of Mitutoyo Digimatic gauges through a Mitutoyo and HNS multiplexer or from the RS232C interface of the measuring projector directly.

Important geometric objects defined in the program:

• linear sizes of the basic geometrical parameters,
• points,
  • centre of gravity,
  • intersection of two lines or intersection of a line and a circle nearest to a given pont,
  • centre of a circle,
• lines,
  • line defined by points,
  • parallel lines,
  • line going through a given point and closing a given angle with a given line,
  • bisector between two lines,
  • line parallel with a line with given distance from it toward a given point,
  • line going through a given point and parallel with a line,
• circles,
  • circle which can drawn into a hole and which can be drawn around a pin,
  • circle given by series of points,
  • circle with a given radius around a given point,
• distances,
  • distance of two points,
  • distance of a line and a point,
  • radius of a circle,
• angles,
• position errors,
  • deviation of parallelity,
  • deviation of a circle centre point and an intersection point of two lines,
  • deviation of circularity,
  • position error,
• shape errors,
  • unlinearity,
  • uncircularity.

Important functions with the geometric objects in the program:

• value settings,
• mathematical operations,
• selecting of maximum or minimum value,
• iteration with changeable parameters,
• comparison, qualification of the measured parameters by the specification given on the drawn.

If you make two dimension measurements with profile projector or measuring microscope, and you want to increase the speed and reliability of these measurements, supporting with computer, please, contact us!

We are ready to make your measuring workstation for two dimensional touch-free measurements. In view of your measuring tasks, we select the most suitable measuring projector or measuring microscope for you, we make the measuring programs needed for measuring of your products and we deliver the workstation, which is suitable and ready for performing the measurements.

Our company design, produce and deliver the fixtures of parts and other accessories needed for measuring of your products.

HNS Technical Development Co. Ltd. • Gesztenyefa 4, Győr, 9027-Hungary | HNS ® • Copyright © 2009-2012 | HNS SPC • Copyright © 1989-2012 | All rights reserved.